Balancing machines are widely used in modern machinery. The choice of lubrication method is also very important. The traditional lubrication method is generally oil lubricated, but in the process of de-weighting, the chips are easy to fall and get stuck on the bearing bush, which affects the de-balancing. Precision.
If the balancing machine bearing bush is made of a small amount of lubrication, it can effectively solve the problem that the chip is easy to fall and jam on the bearing bush to affect the accuracy of the de-balancing, and also obtain various advantages: The use of a small amount of lubrication can reduce the consumption of oil, and save energy. Environmentally friendly;
The operating cost of the micro-lubrication system is very low, the compressed air is the power source of the system, and the energy consumption is low; the problems caused by the chip stuck between the bearing bush and the journal when oil lubrication is used can be reduced;
It can provide good lubrication to the drill bit and extend the life of the cutting tool - the drill bit. Compared with the traditional lubrication method, the advantages of micro-lubrication can be described as many. In order to ensure the micro-lubrication effect, the following two points need special attention:
Dry and stable gas source: The stability of the gas source pressure is an important factor in the normal operation of the micro-lubrication device. The power source of the micro-lubrication device is compressed air, so the stability of the compressed air pressure is very important. The moisture in the compressed air will directly affect the atomization effect, and the lubrication effect will also be affected, so the stability of the gas source pressure and the drying of the gas source are very important.
2. The design of the balance of the oil mist output channel of the balancer bushing is very critical, and its rationality directly affects the lubrication effect of the bearing bush. For the design of the bearing bush, in practical applications, the design channel of the bearing bush does not need to be too large, and the corresponding calculation can be performed according to the size of the journal. The micro-lubrication itself has a small diameter at the lubrication terminal. If the passage is too large, the supply of the air supply is insufficient, and the output of the oil mist is too large, resulting in an impact on the operating environment. Design must be taken seriously.
If the balancing machine bearing bush is made of a small amount of lubrication, it can effectively solve the problem that the chip is easy to fall and jam on the bearing bush to affect the accuracy of the de-balancing, and also obtain various advantages: The use of a small amount of lubrication can reduce the consumption of oil, and save energy. Environmentally friendly;
The operating cost of the micro-lubrication system is very low, the compressed air is the power source of the system, and the energy consumption is low; the problems caused by the chip stuck between the bearing bush and the journal when oil lubrication is used can be reduced;
It can provide good lubrication to the drill bit and extend the life of the cutting tool - the drill bit. Compared with the traditional lubrication method, the advantages of micro-lubrication can be described as many. In order to ensure the micro-lubrication effect, the following two points need special attention:
Dry and stable gas source: The stability of the gas source pressure is an important factor in the normal operation of the micro-lubrication device. The power source of the micro-lubrication device is compressed air, so the stability of the compressed air pressure is very important. The moisture in the compressed air will directly affect the atomization effect, and the lubrication effect will also be affected, so the stability of the gas source pressure and the drying of the gas source are very important.
2. The design of the balance of the oil mist output channel of the balancer bushing is very critical, and its rationality directly affects the lubrication effect of the bearing bush. For the design of the bearing bush, in practical applications, the design channel of the bearing bush does not need to be too large, and the corresponding calculation can be performed according to the size of the journal. The micro-lubrication itself has a small diameter at the lubrication terminal. If the passage is too large, the supply of the air supply is insufficient, and the output of the oil mist is too large, resulting in an impact on the operating environment. Design must be taken seriously.
AWWA Duplex Stainless Steel Flange
AWWA Flanges,AWWA Duplex Flange,AWWA Duplex Stainless Flange,AWWA Duplex Stainless Steel Flange
ShanXi GuanLi Flange Co.Ltd , https://www.sxglflange.com