I. Overview
Hanging bucket garbage truck (hereinafter referred to as garbage trucks) for garbage collection in the town, transport, unloading work material special vehicles. The car is composed of a car chassis, a self-unloading cylinder, a hoist assembly, a top cover (optional), an attached frame, and a garbage box. The operation of the vehicle is accomplished by a hydraulic control system, which can be manual or electronically controlled. The vehicle is mainly used for garbage collection, transportation and unloading of urban garbage. Operate the lift control valve to lift the trash can along with the lifter and turn it to tilt. The garbage in the barrel is dumped into the carriage to complete a single loading of the garbage. The control valve is lifted in the reverse direction and the trash can is lowered along with the lifter; when performed after dump, the dump control valve operation, the hopper body tilt shaft move around the turn, the rear door to open the box, the garbage dump box; from the car by the hydraulic control system of the car to provide complete Hoist The rise and fall and the dumping function of the rubbish reduce the labor intensity of workers and improve the working environment. The garbage truck collection, transportation mode is the way domestic transport garbage collection pan used, its function-specific devices are powered automobile engine, achieved by manual or electric hydraulic mechanism, pneumatic control. Box of the vehicle of high quality carbon steel welded sealed structure having high strength, light weight, dust, underflow and no secondary pollution. The basic performance of the garbage truck is the same as that of the original chassis truck. Users should refer to the original chassis vehicle manual. This manual only describes the relevant operation, inspection and maintenance of the special modification part. Before using the vehicle, we strongly urge you to read this manual thoroughly and to make sure that the operating procedures are handy. Our factory will further improve the product. Product improvement, performance improvement, and constantly improve the structure without notice, so that there is some instructions do not apply to your particular vehicle, please understand.
Second, the structure diagram
Third, the operation steps
Before loading garbage, when the no-load operation reaches 6 standard air pressure, hang up the power take-off device (bottom left of the steering wheel in the cab) and check whether there are any leaks or abnormalities in each component, and then follow the operating procedures; the specific operation steps are as follows: :
Garbage loading
Step 1. First the trash is placed in the hook of the hoist, then lifting or SC (optional) raising the operating handle position to push, lift cylinder of the right tank to the top cover or lid opening extending cylinder The hoisting machine drives the trash can upward and rotates and turns over the garbage, and the garbage enters the box. Release the operating handle to return it to neutral position; as shown in the figure:
Step 2.
The lifting operation lever is pushed to the retracted position, lift cylinder or the right tank to the top cover lid opening cylinders retracted, Titus Hoist driven down bin downwardly and placed on the ground, so releasing operation lever back in place complete a carrier, and then release the power take off may be transported with the car. Also note: If a small scraper is installed in the cabinet, push the handle in the direction of the operation indicator to push the scraper out, push the trash on the front of the cabinet to the back of the cabinet, and reverse the handle before loading the garbage again. Pull back to retract the scraper and return the handle to the neutral position to prevent the garbage from being caught in the front of the scraper and the box and be stuck; if no small scraper is installed in the cabinet, only the front of the box is prevented to prevent rubbish. At this time, the dump handle can be pushed to the open position, and the bottom of the box is extended from the unloading cylinder, so that the box is rotated and lifted to a certain angle around the dump truck, so that the garbage at the front of the box slides to the box due to its own weight. Department, after the completion of the operating handle reverse pull back or return to the center, the box dropped flat release handle.
Garbage dump
When the operation of the vehicle takes hang up to 6 standard gas pressure, and check for leaks after the parts or abnormal, then follow the operation step; step 1. First, after releasing the box door fastening, and then from unloading operation lever is pushed to the open position, the bottom of the box dump cylinders protrude, so that the housing base to rotate about the reversing dump lifted, while the back door to automatically open the box under the impact of weight and waste, garbage discharged; FIG. step 2. after completion of unloading the garbage dump release or reverse the operation lever is pulled back in the tank due to its own weight or under pressure dump cylinder retracted, the drop box firmly to the sub-beam is placed, and finally the lock Close the rear door of the box; release the power take-off trash can and place it, the vehicle can drive
Sodium Hypochlorite Electrolysis Generator
It is controlled by a electrolytic technology to commonly used table salt and water to produce Sodium hypochlorite disinfectant which can effectively disinfect general objects(such as furniture, sanitary ware , meals utensils, floors, fruits, vegetables, etc .);safe environmentally friendly, non-toxic,no side effects and economical affordable.
Electrolysis Generator
SHAOXING SUNSHINE ELECTRONIC CO.,LTD , https://www.crownlamp.com